The most important step in making a good cup of coffee is heat. And you need to be able to control that heat because just a few degrees difference in temperature can turn a great cup into bitter carbon effluence. The Heating System consists of 8 common components: A thermal cut-off, heating elements, thermistor, thermostats, triacs, contactor, fuses and a simple toggle switch. Models can vary widely. Some will have digital controls versus analog and different components, but the principles are the same.
Thermal Cut off – a thermal relay works by breaking the circuit mechanically to the heating elements when it reaches a certain temperature. Sometimes a unit is low on water, and this will cause the elements to exceed its temperature threshold. The relay is attached to the outside of the boiler tank close to the element. They normally cut off at a temperature of 210 –240°F.
Thermistor Sensor – A thermistor is a resistor whose resistance is greatly reduced by heat. The resistance value changes as it cools, or heats then sends messages to the digital board. Digital brewer control boards will control many aspects of the brew cycle, including the thermal system.
A control board on a digital urn uses inputs from the thermistor to monitor the temperature of the tank.
Thermostat – A mechanical thermostat is used to control and maintain the temperature of the water in the heating tank on an analog brewer. A mechanical thermostat is a set of electrical contacts, a capillary, and a bulb. When the boiler water reaches a specific temperature, high pressure is created inside the bulb. This high-pressure pressure then forces the hydraulic fluid through the capillary to the contacts causing them to open the circuit to the heating elements. If the water cools below a certain temp, the pressure in the bulb reduces, the fluid returns into the bulb, and the contacts close.
Triac – A triac is an electronic component that conducts current in either direction when triggered. It is a solid-state device that performs the same function as a relay, without the moving
parts. The Triac allows power to the tank heater. Power will activate when the electronic thermostat calls for heat. When the Control Board turns on the signal, current can flow through the triac to supply heat. Triacs have a very low failure rate.
Fuses and Circuit Breakers – The purpose of a fuse and a circuit breaker is to interrupt the current flow in case of a surge of short circuit. Their primary role it to protect electrical components
Contactor – A contactor is an electrically-controlled switch used for switching an electrical power circuit. It is typically controlled by a circuit which has a much lower power level than the switched circuit. The Thermostat does not have the capacity to carry the total current load of all the elements. A contactor is used in conjunction with the mechanical thermostat. The thermostat controls the on-off action of the contactor depending on the temperature of the water. A contactor consists of a set of contacts which are opened or closed by the magnetic field of its solenoid coil when it is energized by the current
from the primary thermostat.
Heating Elements – A heating element is made up of an electric filament, an insulating heat conductive material, and a jacket. Elements can be a copper jacket or an incoloy (An incoloy is a metal alloy) jacket. Elements come in all sizes, power (wattage) and configurations. Beware; elements should only be powered when they are when they are submerged in water. Out of water the element will overheat, turn red hot, and can burst open causing a short and may injure any person nearby.
Toggle Switch – An electric switch operated by means of a projecting lever that is moved up and down. A toggle switch is used to interrupt the power either to the entire brewer or a section. There are two type of common toggle switches on brewers: Single Pole, Single throw, one set of contacts on and off. Double pole, single throw, two sets of contacts on and off.
With this article on the heating system, we covered all the primary sections of a brewer. This series is intended to be a basic introduction, It does not take place of a solid training course. Its intention is to give you a base knowledge of these units. I have borrowed liberally from several sources to make sure this information is accurate. There are hundreds of different brewers out there that all have different functions to them. The best way to learn about a specific brewer is to take the training course offered by the manufacturer.
The final article in the series will be basic troubleshooting. How to set up a training and a tech test that I have used in training my techs. Feel free and reach out to me at hylanljoseph@gmail.com if you have any requests or questions.
